An IP (Ingress Protection) rating in machine vision lighting tells you how well the light resists dust and water, and in food and beverage manufacturing, that number is often treated as the full story. But there are other considerations. Choosing the right IP rating means matching it to where the light sits in your production line, how it is cleaned and, just as importantly, confirming the housing is genuinely certified and crevice-free.
Machine vision lighting on an automated food or beverage line doesn’t operate in a clean, dry environment. Lights can be hosed down with hot water, blasted with sanitizing chemicals, and mounted inches from products that cannot be contaminated. The IP rating on a datasheet is one of the first considerations for engineers, but the IP rating alone does not always give the full picture. Here’s what IP ratings mean for machine vision lighting, and other features to consider before choosing a light for a washdown environment.
Why IP ratings matter in machine vision lighting
Food safety failures are costly in ways that go beyond a single bad batch. An outbreak traced back to poor hygiene standards carries a direct cost, a reputational one, and in the worst cases a human one, and when sourcing and equipment aren’t properly documented, tracing the source back through the supply chain takes longer and costs more. As machine vision takes over inspection tasks once completed by hand: checking size, shape, color and defects on everything from packaged snacks to raw produce, the cameras and lights used in those inspections are moving closer to the product, and closer to the wash-down cycle. An IP rating is the first line of defense: it describes whether water and contaminants can get inside the light at all.
What does an IP rating actually mean?
IP stands for Ingress Protection. It is a two-digit code defined in IEC 60529, describing how well an enclosure resists solid objects and liquids getting inside. The first digit is for solids, and the second is for liquids. For washdown environments in food and beverage production, IP69K is seen as the standard: it certifies that a light can withstand close-range, high-pressure, high-temperature water jets, the kind of treatment used to sanitize equipment between production runs.
An IP rating is a necessary starting point for choosing machine vision lighting in food and beverage production, but it isn’t the finish line. The right choice comes down to matching the rating to the zone, choosing a housing material that survives the specific cleaning chemistry involved, and confirming the geometry is genuinely crevice-free and self-draining. UltraSeal™ Washdown Lights were built around exactly that combination.
Common IP ratings you’ll see on machine vision lighting
| Rating | Typical protection | Typical machine-vision use |
|---|---|---|
| IP64 | Splash-proof from any direction | Light-duty areas, minimal wash-down |
| IP65 / IP66 | Low-pressure to powerful water jets | General production floor, periodic hose-down |
| IP67 | Temporary immersion up to 1m | Occasional deep cleaning, non-critical zones |
| IP69K | High-pressure, high-temperature jets at close range | Direct washdown, splash and food-contact zones |
IP69 vs IP69K. Is there a difference?
Both IP69 and IP69K are used in machine vision lighting, sometimes interchangeably. IP69K originally comes from DIN 40050-9, a German standard developed for washing down road vehicles and heavy industrial equipment. IEC 60529 later added a very similar test as “IP69” in a 2013 amendment, extending it to general industrial use. In practice, the pressure, temperature and distance specified by the two tests are close enough that washdown resistance is nearly identical. The most important difference is which standards body backs the certification, and what documentation comes with it.
How to choose the right IP rating for your application
Not every light on a production line needs to be rated for the harshest washdown. Requirements generally scale down as equipment moves further from direct product contact:
| Hygiene zone | Typical exposure | Typical IP guidance |
|---|---|---|
| Food Contact Zone | Direct contact / full washdown | IP69K generally preferred |
| Splash Zone | Near product, indirect exposure | IP66–IP69 range |
| Non-Product Zone | General processing room | IP65–IP67 often sufficient |
| External Zone | Outside the production room | Standard industrial enclosure often enough |
Beyond the zone, a few practical questions decide how much protection is actually needed: How often does the equipment get washed down, and with what? Is the residue a fine powder or grease (harder to remove, requiring more pressure and heat) or something coarser? And how close is the light to the inspection point? For example, is it mounted safely to the side, or hanging directly over a fryer?
Beyond the number: why materials and geometry matter just as much
An IP rating only tells you whether a sealed housing keeps water out today. It says nothing about whether the housing survives repeated exposure to the specific chemicals used to clean it, or whether its shape actually lets water and residue drain away rather than pool.
Material choice
| Stainless steel | Anodized aluminum | |
|---|---|---|
| Chemical resistance | Best (handles caustic / highly corrosive washdown chemistry) | Good for less demanding environments |
| Thermal performance | Poor (traps heat) | Much better (helps dissipate heat from the LEDs) |
| Cost / weight | Heavier, more expensive | Lighter, more economical |
| Best fit | Highly caustic or corrosive washdown areas | General washdown, less aggressive chemistry |
Geometry
- A minimum self-draining slope, so water doesn’t pool on top of the housing.
- A smooth surface finish. Rough surfaces harbor bacteria.
- Generous corner radii, avoiding sharp 90° corners.
- As few fasteners, threads and joints as possible. Each one is a potential residue trap.
It is also important to note that not every IP rating on a datasheet has been through independent certification. Some ratings are self-declared rather than verified by a third party.
Where UltraSeal™ washdown lights fit in
This is exactly the gap Advanced Illumination’s UltraSeal™ Washdown LED Lights were engineered to close, bringing all three considerations together in a single product line rather than leaving engineers to solve them separately:
- IP69K certified through a formal, independent certification process rather than a self-declared rating.
- A patented, virtually crevice-free housing designed so debris and moisture can’t collect around bolts or seams on the face of the light.
- A choice of housing material: stainless steel or anodized aluminum where the environment is less demanding without a custom design project.
- An all-in-one sealed design, so the light itself is the enclosure.
- Available as Ring, Bar, Spot and Backlight configurations, positioned for Non-Product and up to Splash-zone use in food and beverage production.
Watch the UltraSeal backlight video on YouTube, which shows how UltraSeal backlights are designed for demanding washdown machine vision applications.
Explore the UltraSeal™ Washdown Lights range to find the configuration that fits your production line, or get in touch with the team for guidance on the right IP rating and housing material for your application.
FAQ
Is IP67 enough for a washdown environment?
It depends on the zone. IP67 protects against temporary immersion, but food-contact and splash zones with routine high-pressure, high-temperature washdown typically call for IP69K.
What’s the difference between a self-declared and a certified IP rating?
A self-declared rating is the manufacturer’s own claim; a certified rating has been independently tested by an accredited laboratory against the IP standard.
Do I need IP69K everywhere on my line?
No. Requirements generally scale down as equipment moves further from direct product contact, from the food contact zone, to splash zone, to non-product and external zones.
What’s the difference between IP69 and IP69K?
Both use a near-identical high-pressure, high-temperature washdown test. The main difference is which standards body governs the certification (IEC/ISO versus the original German DIN standard) and the documentation behind it.
Can a light have a high IP rating and still fail a hygienic design audit?
Yes. An IP rating covers ingress protection only. If the housing traps water in crevices or on flat surfaces, it can still fail EHEDG-style hygienic design criteria even with a high IP number.
Hygienic Design for Machine Vision in Food and Beverage Washdown
Download the white paper Explore UltraSeal™